Replace 400 default_materials entries that referenced an unknown filament
(92) or a filament not compatible with the model (308) with the most-
specialized compatible same-type material, as flagged by the new
check_default_materials validator. Bump the 21 touched vendor versions so
the fixes reach existing installs.
* fix profile reference for Creality
* fix profile reference for Blocks
* fix profile reference for OrcaArena
* fix profile reference for re3D
* fix profile reference for Chuanying
* fix profile reference for Prusa
* fix profile reference for Wanhao France
* fix profile reference for MagicMaker
* fix profile reference for Afinia
Remove the ABS/ABS+/PLA/TPU/Value ABS/Value PLA filament presets that referenced the non-existent "Afinia H400 Pro" printer. The real printer is "Afinia H+1(HS)", already served by the @HS filament variants.
* fix profile reference for Comgrow
Remove the orphaned "0.20mm Standard @Comgrow T500 1.0" process preset and its process_list entry. Its only compatible printer "Comgrow T500 1.0 nozzle" never existed (the T500 model defines nozzle diameters 0.4/0.6/0.8 only).
* always run check_preset_references
The 409 conflict notification, the force-push confirmation dialog, and the payload-too-large (413) dialog now name the affected preset. The name was already parsed from the conflict body but never surfaced. The account-level preset-limit message stays generic since it isn't about one specific preset.
* Fix reload from disk for STEP models after reopening a project (#12992)
reload_from_disk matched reloaded source volumes with an exact
source.input_file string comparison. After a project is saved and
reopened, the stored source path is only the filename (the default,
non-full-path save) while a freshly re-imported volume carries a full
path, so the comparison never matched: reload fell into fail_list and
the "locate file" dialog was effectively useless for STEP models.
Fall back to a case-insensitive filename comparison when the exact
paths differ, so the existing same-folder source lookup (and the
locate dialog) can reload the model. Projects that stored absolute
source paths still match exactly as before; no 3mf format change.
* Add Preferences option to store full source paths in projects
Expose the existing export_sources_full_pathnames setting (previously
only editable in the config file) as a checkbox under Preferences >
General > Project. Enabling it stores absolute source paths in saved
projects, so "Reload from disk" works when the source file is kept in
a different folder than the project (companion to #12992).
* fix: crash in Measure tool when a plain edge is the first selection
The SPHERE_2 gripper raycaster called get_feature_offset() on
.first.feature instead of .second.feature (copy-pasted from the SPHERE_1
block). Plain planar-border edges store no extra point, so the Edge
branch dereferenced an empty optional behind a release-stripped assert,
aborting on Flatpak and undefined behavior elsewhere.
Point the SPHERE_2 raycaster at .second.feature and fall the Edge branch
back to the edge midpoint.
Fixes#14018
{input_filename_base} is meant to be the saved project's file name. Before
#13753 a bug made it fall back to the first object's name when a project was
saved; #13753 fixed it to use the project name. Some users relied on the old
behavior to get the part name into their output file name and had no
placeholder to recover it ({model_name} is the 3mf designer metadata, blank
for plain STL imports).
Add {first_object_name} as a dedicated placeholder for the first printable
object on the current plate, populated in update_object_placeholders()
independently of {input_filename_base}.
Closes#14493
Selecting the prime tower and rotating it (PageUp/PageDown) crashed.
Selection::notify_instance_update() indexed m_model->objects with the
wipe tower's synthetic id (>= 1000), which is not a ModelObject index,
so the lookup returned garbage and dereferencing it segfaulted.
do_rotate/do_scale/do_mirror already skip the wipe tower in their own
loops but all call this shared helper, so scale and mirror hit the same
fault. Selection::drop() had the same latent bug via a direct index.
Guard both with the >= 1000 check already used throughout the file.
Fixes#14498
* Support accessing `coFloatsOrPercents` values in gcode template (OrcaSlicer/OrcaSlicer#14522)
* Vector option values are separated by comma
* Fix wrong cast used for checking nullability
Fix network plug-in install failing when the plug-in DLL is in use (#14373)
Switching or reinstalling the Bambu network plug-in from a running
OrcaSlicer failed with "The plug-in file may be in use". install_plugin()
deleted each existing file before extracting the new one, and on Windows a
currently-loaded DLL (BambuSource.dll, or the legacy networking library)
cannot be removed or overwritten in place, so the whole install aborted.
Rename an in-use file aside to "<name>.old" before writing the new one: the
running module keeps mapping the renamed file while the new version is
extracted, so the install succeeds without having to unload the plug-in
first. Stale ".old" files are cleaned up at the start of on_init_network(),
before the plug-in is (re)loaded, so they do not accumulate.
# Description
This PR expands profile validation so we can catch backward
compatibility issues with custom presets generated by older OrcaSlicer
releases. It also adds missing `renamed_from` metadata for presets that
were renamed or moved, so older user presets can resolve their original
parent names against the current system profiles.
## Background
Many users have reported missing preset issues after upgrading past
2.4.1. Investigation showed two common causes:
- preset lookup and compatibility checks did not always account for
`renamed_from`
- some renamed base presets were missing the old preset name in their
`renamed_from` metadata
The existing profile workflow validates the current system profile tree
and a single nightly-generated custom preset bundle. That is useful for
catching current profile errors, but it does not validate user presets
generated by older OrcaSlicer versions against the current system
profiles. As a result, older missing-parent compatibility gaps can slip
through.
## Changes
- Update `check_profiles.yml` to validate historical custom preset
fixtures from `OrcaSlicer/OrcaSlicer-profile-validator`.
- Download the fixture manifest from the public `fixture-archive`
release.
- Validate each `orca_custom_presets_<version>.zip` fixture
independently against the current PR's `resources/profiles`.
- Generate per-version validation logs and upload them as workflow
artifacts.
- Fail profile validation if any historical fixture version fails.
- Add missing `renamed_from` aliases for renamed/moved presets found by
the historical fixture validation.
## Profile Compatibility Fixes
This PR adds aliases for older parent names including:
- `0.20mm Bambu Support W @BBL X1C` -> `0.20mm Standard @BBL X1C`
- `Bambu PLA Impact @BBL X1C` -> `Bambu PLA Impact @System`
- `Ginger Generic rPLA` -> `Ginger Generic PLA`
- `Ginger Generic rPETG` -> `Ginger Generic PETG`
- legacy `Panchroma PLA Stain` BBL filament names -> current `Panchroma
PLA Satin` names
- legacy Elegoo casing/name variants such as `Elegoo RAPID PLA+`,
`Elegoo RAPID PETG`, `Elegoo RAPID PETG+`, and `Elegoo PETG Pro @System`
## Validation Flow
The custom preset validation step now:
1. Downloads `manifest.json` from the `fixture-archive` release.
2. Iterates over every fixture listed in the manifest.
3. Copies the current branch's `resources/profiles` into a temporary
profile tree.
4. Removes any existing `user` directory from that temporary tree.
5. Unzips exactly one historical fixture into the temporary tree.
6. Runs `OrcaSlicer_profile_validator -p <temp profile tree> -l 2`.
7. Writes a version-specific log and a consolidated summary.
This keeps validation scoped per fixture version and avoids mixing
generated user presets from different OrcaSlicer releases.
## Fixture Source
Historical fixtures are stored as public release assets in:
`OrcaSlicer/OrcaSlicer-profile-validator`, release tag `fixture-archive`
Each release asset is expected to be named like:
```text
orca_custom_presets_v2.4.1.zip
```
## Testing
Validated locally with:
- current system profile validation
- BBL filament subtype validation
- historical custom preset fixture validation
- extra profile JSON check in a clean profile tree
The affected historical fixture set passed after adding the missing
`renamed_from` aliases.
The release manifest controls which fixture versions are validated.
[How to Download Pull Requests Artifacts for
Testing](https://www.orcaslicer.com/wiki/how_to_download_pr_artifacts)
Remove the orphaned "0.20mm Standard @Comgrow T500 1.0" process preset and its process_list entry. Its only compatible printer "Comgrow T500 1.0 nozzle" never existed (the T500 model defines nozzle diameters 0.4/0.6/0.8 only).
Remove the ABS/ABS+/PLA/TPU/Value ABS/Value PLA filament presets that referenced the non-existent "Afinia H400 Pro" printer. The real printer is "Afinia H+1(HS)", already served by the @HS filament variants.
# Description
There is a bug that if user used to use legacy plugin, the
`NetworkAgent::use_legacy_network` will not be properly reset after user
install a newer plugin version through the plugin update dialog (ie, not
from selecting a plugin version from Preference screen). And in that
case Orca will download the legacy plugin but instead installing it with
a newer version suffix. So on next start up Orca can't find the plugin
because it tries to load using legacy version suffix instead.
This PR fixes it by getting rid of that error-prone static variable,
instead it always use the version number directly.
Fix#14373Fix#14441
# Screenshots/Recordings/Graphs
<!--
> Please attach relevant screenshots to showcase the UI changes.
> Please attach images that can help explain the changes.
-->
## Tests
<!--
> Please describe the tests that you have conducted to verify the
changes made in this PR.
-->
<!--
> A guide for users on how to download the artifacts from this PR.
-->
[How to Download Pull Requests Artifacts for
Testing](https://www.orcaslicer.com/wiki/how_to_download_pr_artifacts)
# Description
Fixes user filament presets that reference an old printer preset name in
`compatible_printers`, even when the current system printer preset
correctly declares that old name in `renamed_from`.
## Core Issue
`PresetCollection::find_preset()` was updated to resolve `renamed_from`,
but this specific failure does not go through `find_preset()`.
For root user filament presets with empty `inherits`, Orca infers
`compatible_printers` from the filament name suffix after `@`. For
example:
```json
"ELEGOO PLA Base @Elegoo Neptune 4 Pro (0.4 nozzle)"
```
loads with:
```json
"compatible_printers": ["Elegoo Neptune 4 Pro (0.4 nozzle)"]
```
The current system printer preset is named:
```text
Elegoo Neptune 4 Pro 0.4 nozzle
```
and has:
```json
"renamed_from": "Elegoo Neptune 4 Pro (0.4 nozzle)"
```
However, filament compatibility was doing a direct string comparison
against the active printer name. Since that compatibility path does not
call `find_preset()`, the `renamed_from` mapping was never considered.
## Fix
Teach printer compatibility checks to treat
`active_printer.preset.renamed_from` entries as aliases of the active
printer name.
This preserves existing user preset JSON and avoids rewriting
`compatible_printers`, while allowing old printer suffixes to remain
compatible with renamed system printer presets.
## Tests
<!--
> A guide for users on how to download the artifacts from this PR.
-->
[How to Download Pull Requests Artifacts for
Testing](https://www.orcaslicer.com/wiki/how_to_download_pr_artifacts)
* Add startup progress bar to splash screen
* Move progress bar down and remove percentages
* Cleaned up changes
* Update GUI_App.cpp
---------
Co-authored-by: yw4z <ywsyildiz@gmail.com>
WipeTowerIntegration::append_tcr processed filament_end_gcode with only
layer_num in its placeholder config, so a filament_end_gcode referencing
{layer_z} could not be evaluated and slicing aborted. This affects any
multi-filament print that routes tool changes through the prime/wipe tower
(for example a support filament on a Bambu printer); the same macro works
in machine_end_gcode and on the non-wipe-tower set_extruder path, which
both define layer_z.
Set layer_z to tcr.print_z, the value this function already provides to its
change_filament_gcode and tcr_rotated_gcode placeholders.
Fixes#10119
PR #13712 fixed the uninitialized Print::m_origin (commit 99dea01cc3, "Fix coord
out-of-range exception caused by m_origin memory not initialized to 0") that made
headless slice() intermittently throw ClipperLib's "Coordinate outside allowed
range". With that root cause fixed, the three tests disabled for it pass again,
so drop their [NotWorking] tags.
CalibPressureAdvancePattern::line_width_first_layer() returned the raw
initial_layer_line_width, so a value of 0 (which means "use the default")
fed 0 into the Flow spacing math and threw FlowErrorNegativeSpacing,
crashing the whole app when slicing a PA pattern calibration.
Mirror the guard already present in the sibling line_width(): when the
configured width is non-positive, fall back to auto_extrusion_width.
Add a libslic3r regression test covering the width resolution.
Fixes#13188
* validator: detect duplicate filament subtype per printer (opt-in)
A filament is matched from the AMS by (filament_id + printer compatibility);
if two compatible filament presets for one printer share a filament_id, the
match is ambiguous and the runtime silently picks whichever loads first.
Add PresetBundle::check_duplicate_filament_subtypes(), gated behind a new
has_errors(check_duplicate_filament_subtypes) parameter and the validator's
-f/--check_filament_subtypes flag (off by default). For each system printer it
groups its vendor's compatible filament presets by filament_id and errors on
any group of 2+, reporting each preset as a clickable file:// URI with a single
"how to fix" hint. CI runs it for BBL only (-v BBL -f) until the other vendors'
profiles are cleaned up.
* profiles: fix ambiguous BBL filament matches
Resolve the duplicate-filament-subtype errors flagged by the validator:
- align compatible_printers with Bambu Studio where Orca over-claimed a nozzle
that already has a dedicated preset (Bambu PLA Basic/Matte/ABS @BBL H2DP;
Bambu ASA/PETG HF @BBL H2DP 0.6 nozzle; Fiberon PETG-ESD @BBL X1)
- fix a copy-pasted printer name in Overture Matte PLA @BBL A1M 0.2 nozzle
- fix a wrong inherits in Panchroma PLA Silk @BBL X1C 0.2 nozzle (was inheriting
Panchroma PLA @base, giving it filament_id GFPM001 instead of GFPM004)
Bump BBL profile version.
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* profiles: enforce globally-unique, per-vendor-namespaced setting_id
Many non-Bambu vendors copied Bambu's generic setting_ids (GFSA04 alone
appeared in 1557 files), so setting_id was not globally unique. This
namespaces every vendor's ids and reserves Bambu/OrcaFilamentLibrary space.
- Reserve "G*" (Bambu) and "O*" (OrcaFilamentLibrary) id spaces.
- Assign each other vendor a 2-char prefix (first+last letter, collision
resolved) and renumber every instantiated preset to <PREFIX><NNNN>.
- Strip setting_id from base profiles (instantiation:false) per Bambu's
convention; assign one to instantiated presets that lacked it.
- Remove the pre-existing misspelled "settings_id" key (91 files).
- filament_id is left untouched (it is a per-material id).
- Add one-time migration script scripts/assign_vendor_setting_ids.py with a
persisted registry resources/profiles/vendor_prefixes.json. Re-runs freeze
existing ids; only new vendors/profiles get new ids.
- Bump version in each changed vendor index file.
- Extend scripts/orca_extra_profile_check.py with a CI guard: global
uniqueness, in-namespace, no base setting_id, no gaps, no settings_id typo.
7425 profile files changed across 61 vendors; 0 cross-vendor collisions;
validator clean; migration idempotent. BBL and OrcaFilamentLibrary id spaces
untouched.
* profiles: add setting_id authoring guide for new vendors / profiles
* profiles: drop in-repo README; setting_id guide now lives in the wiki
* profiles: derive setting_id deterministically from vendor/type/name
* bump profile version
* Resolve preset type based on nozle diameter if printer_variant is empty
* Fix incorectly resolving plastic type (PLA, ABS, etc.)
* Revert default print-variant handling as it can be not only nozzle diameter
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* CrealityPrint: use printhost_port for WebView URL instead of hardcoded :4408
Fixes#4408 — when printhost_port is configured, use that port in the
Device WebView URL instead of always defaulting to :4408.
* CrealityPrint: remove hardcoded :4408 from Device WebView URL
Drop the CrealityPrint-specific get_print_host_webui override that
unconditionally appended :4408. The generic fallback in PrintHost
already uses print_host_webui/print_host config — users who need
Mainsail on port 4408 should set print_host_webui explicitly.
Fixes#4408
Syncing the filament list from AMS with the "Overwriting" option
displayed the AMS filaments in the wrong (reversed) order in the
preview, even though the filament mapping that was actually applied
was correct. Reported on macOS with a Bambu X1C.
The preview depends on MaterialHash being iterated in material-index
order. MaterialHash is a WX_DECLARE_HASH_MAP, which under OrcaSlicer's
current wxWidgets 3.3 build (wxUSE_STD_CONTAINERS=1) resolves to
std::unordered_map; its iteration order is unspecified and on macOS
(libc++) comes out reversed, which scrambled the preview. The same
code is unaffected in BambuStudio because its older wxWidgets build
still uses wx's own key-ordered hash table, so this only became
visible after the wx upgrade.
Fixes#14335
* feat: native Windows ARM64 build support
Builds on the merged DEPS_ARCH=arm64 plumbing (#13424) by adding the
dependency and source fixes needed for a green native ARM64 build on the
windows-11-arm runner. Validated end-to-end on Snapdragon X Elite hardware
(via a downstream fork using the same fixes); see OrcaSlicer/OrcaSlicer#8271
for the full writeup.
Dependencies:
- OpenEXR 2.5.5: ImfSimd.h hard-codes IMF_HAVE_SSE2 for any MSVC, pulling in
<emmintrin.h> (x86-only) -> C1189. Patch the header to require an x86 target
and force SSE cache vars off on ARM64.
- Boost.Context: use the winfib implementation on ARM64 (Windows Fiber API)
to avoid the armasm64 / CMake ASM_ARMASM linker-module bug, while keeping
the Boost::context target Boost.Asio needs.
- OpenCV: disable WITH_IPP on ARM64 (Intel IPP/IPP-ICV is x86/x64 only;
otherwise ~200 unresolved ippicv* externals at link).
- OpenSSL: use VC-WIN64-ARM on ARM64.
- FindGLEW: add an ARM64 arch branch.
Sources:
- clipper Int128.hpp: _mul128 is an x64-only intrinsic guarded by _WIN64
(true on ARM64); guard on _M_X64 and use the portable path.
- imgui imgui_widgets.cpp: fix va_start(vaList, &text) -> va_start(vaList, text)
(the &-form compiled on x64 but is invalid on ARM64).
- crash reporter: StackWalker.cpp gains an _M_ARM64 branch; BaseException.cpp
uses Cpsr instead of the x86-only EFlags on ARM64.
CI:
- New build_windows_arm64.yml on windows-11-arm: pins CMake 3.31.x, stages
ARM64 GMP/MPFR from MSYS2 clangarm64 (with llvm-dlltool import libs),
caches deps with a fixed-depth hashFiles key, builds and uploads the binary.
OCCT/STEP, SVG-to-3D and text emboss all build and work on ARM64 (no stubs
needed). Full feature parity with x64.
* fix(ci): use forward-slash DESTDIR to avoid CMake '\a' escape error
deps configure failed at GMP/GMP.cmake: "Invalid character escape '\a'"
because DESTDIR carried Windows backslashes (C:\a\...) and is re-parsed
when re-set with the /usr/local suffix. Pass DESTDIR (and the slicer's
DEPS prefix) with forward slashes via %CD:\=/%.
* fix(ci): don't export DESTDIR env var (CMake staged-install doubles paths)
Setting a DESTDIR *environment* variable made CMake treat it as the staged
install prefix and prepend it to every dependency's install path, so e.g.
FreeType installed to <DESTDIR>/a/.../OrcaSlicer_dep/usr/local and OCCT
then couldn't find its headers. Compute the forward-slash path into a
differently-named var (ORCA_DESTDIR) and pass it only via -DDESTDIR.
* ci(windows-arm64): fold ARM64 build into the standard Windows matrix
Replace the standalone build_windows_arm64.yml with a matrix entry on the
existing build_windows job, so x64 and ARM64 share one reusable workflow
chain (build_all -> build_check_cache -> build_deps -> build_orca), per
review feedback on #14059.
- build_all.yml: build_windows now matrices over {x64: windows-latest,
arm64: windows-11-arm} and threads `arch` through. Self-hosted runner
stays x64-only.
- build_check_cache.yml: cache key and dep-prefix path are now
architecture-specific on Windows (deps/build-arm64/OrcaSlicer_dep).
- build_release_vs.bat: accept an `arm64` argument (mirrors
build_release_vs2022.bat) -> uses `-A ARM64` and the build-arm64 tree.
The top-level CMake auto-derives CMAKE_PREFIX_PATH from the build dir,
so no explicit prefix is needed.
- build_deps.yml / build_orca.yml: gate the ARM64-only prep behind
`inputs.arch == 'arm64'` -- pin CMake 3.31.x, and stage MSYS2
clangarm64 GMP/MPFR import libs. NSIS installer/PDB/profile_validator
remain x64-only; ARM64 ships the portable zip. Artifact names get an
arch suffix to avoid collisions between the two Windows jobs.
https://claude.ai/code/session_0164c7ZhCLsYBmCiVN9pWDjK
* ci(temp): generate GMP/MPFR win-arm64 blobs to commit to repo
* feat(deps): add prebuilt GMP/MPFR win-arm64 blobs
The repo ships prebuilt GMP/MPFR import libs + DLLs for win-x64 and
win-x86; the Windows ARM64 build path copies from win-${DEPS_ARCH}
(CMakeLists.txt) but the win-arm64 blobs were missing, so the slicer
configure failed at "file COPY cannot find .../win-arm64/libgmp-10.dll".
Add win-arm64 libgmp-10.{dll,lib} and libmpfr-4.{dll,lib}, generated from
the MSYS2 clangarm64 gmp/mpfr packages with MSVC-compatible import libs via
llvm-dlltool. Headers are shared across arches and unchanged.
* simplify OpenEXR.cmake
* set default arch
* support msix
* ship installer
* try to fix webview2runtime issue
---------
Co-authored-by: Adam Behrman <adam.behrman@gmail.com>
Co-authored-by: Claude <noreply@anthropic.com>
Co-authored-by: Adam Behrman <abehrman@users.noreply.github.com>
fix(profiles): add printable_area to fdm_U1 so all nozzle variants inherit correct 270x270 bed
The 0.2/0.6/0.8 nozzle profiles inherit from fdm_U1 which had no
printable_area defined, causing them to fall back to a smaller default
bed size. The 0.4 profile was the only one that set it explicitly.
Move printable_area and printable_height to the shared parent (fdm_U1)
so all Snapmaker U1 nozzle variants get the correct 270x270mm bed.
Bump vendor version to trigger profile re-sync on existing installs.
Co-authored-by: ni4223 <ni4223@users.noreply.github.com>
feat: forward plateindex for index-coded .gcode.3mf uploads
Gcode inside a .gcode.3mf is index-coded (Metadata/plate_<N>.gcode) and a
bundle may carry several, so the upload must name which plate to print —
even a single-plate bundle, since its entry is still indexed.
A 1-based plate index is stored in PrintHostUpload::extended_info when use_3mf
is set; the OctoPrint and Moonraker hosts forward it as a `plateindex` form
field. Servers that don't use it ignore the unknown field, so the plain G-code
path is unchanged.
Refactor skirt and brim ownership and emission flow
Refactor skirt and brim generation around a common object/group
ownership model.
Skirts and brims are now emitted as a coordinated preamble
(skirt -> brim -> object) instead of being generated and emitted
through multiple independent code paths.
Changes:
- Fix repeated skirt emission caused by the previous skirt state
tracking logic.
- Restore local skirt/brim ordering for per-object skirts in
By Layer mode.
- Emit brims together with their owning object or object group.
- Handle combined brims independently from skirt grouping.
- Handle draft shields through the same ownership model as skirts.
- Fix draft shield generation when skirt height is zero.
- Generate draft shields after brim geometry is known, preventing
draft shields from overlapping brims.
- Reject unsafe grouped per-object skirt configurations in
By Object mode.
- Remove legacy skirt emission paths and state-management
workarounds.
Support brim generation remains unchanged.
Co-authored-by: SoftFever <softfeverever@gmail.com>
The `@FF AD5M 0.25 nozzle` filament variants carried the base profile's
full printer list (AD5M/AD5M Pro/AD5X 0.4/0.6/0.8) instead of the 0.25
nozzle printers. Combined with base profiles that also listed the AD5X
0.4/0.6/0.8 printers already covered by dedicated `@FF AD5X` variants,
multiple presets with the same alias became compatible with the same
printer. The filament combobox keys presets by full name but displays
them by alias, so these surfaced as duplicate entries (e.g. "Flashforge
PLA Silk", "Flashforge ASA Basic" shown twice).
Fix the `compatible_printers` lists (data only, no settings changed):
- Repoint the 15 `@FF AD5M 0.25 nozzle` variants to the actual 0.25
nozzle printers (Adventurer 5M 0.25 + Adventurer 5M Pro 0.25).
- Remove the redundant AD5X 0.4/0.6/0.8 entries from the base profiles
where dedicated AD5X variants already exist.
- Bump Flashforge profile version to 02.04.00.02.
Each affected filament now resolves to exactly one preset per printer,
and the previously uncovered AD5M 0.25 nozzle printers gain coverage.
* Snapmaker U1: add 0.2mm and 0.8mm nozzle profiles
Add machine and process profiles for the Snapmaker U1's 0.2mm and
0.8mm nozzles, and complete the 0.6mm process lineup. Follows the
same data-only pattern used to add the 0.6 / 0.4+0.6 nozzles in
commit afc3756.
The U1 ships with 0.4, 0.4+0.6 and 0.6 nozzle options today; the 0.2
and 0.8 nozzles are supported hardware but have no profiles, so they
cannot be selected. This adds them the Orca-native way: per-nozzle
machine presets plus a model-file dropdown entry, with their process
profiles filtered in via compatible_printers.
Machine (2): lean presets inheriting fdm_U1, mirroring the existing
SM_U1_06 (0.6) preset and overriding only the per-nozzle values;
setting_ids SM_U1_02 / SM_U1_08.
Process (21): 2 per-nozzle commons (fdm_process_U1_0.2_common,
_0.8_common) holding the nozzle line widths, plus 19 profiles
(0.2: 8, 0.6: 6, 0.8: 5) that inherit their per-nozzle common and
carry their own layer height, matching upstream's factoring. The two
0.24 Standard profiles that shared id GP029 are split into
GP029_06_024 / GP029_08_024.
Model dropdown: machine/Snapmaker U1.json nozzle_diameter
"0.4;0.4+0.6;0.6" -> "0.2;0.4;0.4+0.6;0.6;0.8".
Vendor index: register the new presets in Snapmaker.json.
The existing 0.4 / 0.6 / 0.4+0.6 presets resolve identically before
and after. scripts/orca_extra_profile_check.py and the profile
validator both pass.
* chore(profiles): bump Snapmaker vendor version to 02.04.00.04
Bump the Snapmaker vendor config_version so existing installs pick up the new 0.2mm and 0.8mm U1 nozzle profiles. PresetUpdater only re-imports a vendor bundle when the shipped version is strictly greater than the cached one.
---------
Co-authored-by: ni4223 <ni4223@users.noreply.github.com>
K1C: corrige erro 'End of file' ao enviar impressao (start_print)
A K1-family fecha o WebSocket 9999 assim que aceita o comando de iniciar
impressao. O start_print fazia um ws.read() bloqueante logo apos o write, que
estourava 'End of file [asio.misc:2]' e era reportado como erro -- embora a
impressao ja tivesse iniciado (o comando e entregue no write). Torna o read e o
close best-effort (overloads com error_code), eliminando o falso erro. Mesmo
padrao ja usado em feed_filament; cobre os caminhos single-color e multicor.
Several Artillery and Flashforge machine profiles set the first-layer nozzle temperature with M104 (set, no wait) immediately before the purge/prime line. The purge then runs before the nozzle reaches temperature, so filament is extruded through a nozzle that is not yet hot enough to melt it. Changed M104 to M109 so the printer waits for the target temperature before purging.
Affected profiles:
- Artillery Sidewinder X3 Plus / X3 Pro / X4 Plus / X4 Pro (0.4 nozzle)
- Flashforge AD5X (0.25/0.4/0.6/0.8)
- Flashforge Adventurer 5M / 5M Pro (0.25/0.8 overrides + shared fdm_adventurer5m_common, which also covers the 0.4/0.6 variants via inheritance)
Refs #4337
Build the Linux AppImage for ARM64 (aarch64) alongside x86_64: the Linux CI
job now matrixes over both architectures, with arch-aware deps caching and
artifact/asset names (amd64 keeps its existing names). The aarch64 AppImage is
published to the nightly and release pages like the x86_64 one.
Run the unit-test suite on the aarch64 runner (faster GitHub arm runner); the
tests are built on that leg. Self-hosted keeps tests on the amd64 server.
* fix(libnest2d): skip the excluded-region alignment pass when there are none
NfpPlacer::finalAlign(), run from clearItems() and the destructor, always
ran the "find a best position inside the NFP of fixed items" pass even when
no items are fixed. With nothing to avoid, calcnfp() computes the inner-fit
NFP of the pile and can feed clipper a coordinate outside its allowed range.
On Linux/clang the value stays in range so it went unnoticed; on MSVC the
clipper "Coordinate outside allowed range" exception escapes the noexcept
destructor and aborts the process (exit 0xC0000409).
Build the excluded set up front and only run the pass when it is non-empty.
The block exists solely to keep the pile clear of fixed items (excluded
regions / wipe tower), so it is a no-op when there are none and the
wipe-tower behaviour is unchanged.
* test(libnest2d): remove dead nesting tests and split the suite by feature
Seven of the suite's hidden [.] test cases drove code paths Orca abandoned
at the BambuStudio fork: BottomLeftPlacer (used nowhere in src/) and the
stock default NfpPlacer backend, which returns zero bins in Orca. They have
been red since the fork and are never registered with ctest. Remove them.
Split the 1,000-line libnest2d_tests_main.cpp into per-feature files, per the
repo convention, sharing a header for the no-fit-polygon backend setup that
every translation unit must agree on (ODR):
libnest2d_tests.cpp Item and nest() basics
test_geometry.cpp geometry primitives
test_nfp.cpp no-fit-polygon machinery
libnest2d_test_utils.hpp shared includes and the NFP backend specialisation
Along the way: drop a debug exportSVG() helper that only wrote a file on test
failure (so the suite never leaves stray assets), convert the deprecated
Catch::Approx to WithinRel/WithinAbs matchers, and give the tests descriptive
names.
* test(libnest2d): add NfpPlacer unit tests
NfpPlacer is the placement engine the arranger drives, but the suite only
covered the geometry primitives. Add a fixture and five tests that exercise
pack()/accept() directly: a single item lands in the bin, an oversized item
is rejected, the first item is seeded for every starting point, many items
pack without overlap, and the rotation candidates are searched. This lifts
nfpplacer.hpp line coverage from 42% to 87% in the libnest2d suite.
* test(libslic3r): add arrangement::arrange() integration coverage
The libnest2d suite cannot reach Orca's real nesting entry point because it
does not link libslic3r. Add test_arrange.cpp driving arrangement::arrange():
items land on the bed and within bounds, do not overlap, are spaced by their
inflation, an oversized item stays unplaced, overflow spills onto virtual beds,
an empty input is a no-op, and the DONT_ALIGN and USER_DEFINED final-alignment
paths are exercised. A self-test guards the overlap check the other cases use.
* APA for overhangs - Prusa incompatibility warning
Added a sentence explicitly stating that APA for overhangs is not compatible with prusa printers
* whitespace
Clarify that "network plugin" now means *bambu* only and doesn't refer to orca cloud
fully differentiate the two offerings to avoid confusion especially for non Bambu users
@@ -146,16 +146,16 @@ text = Fine-tuning for flow rate\nDid you know that flow rate can be fine-tuned
text=Split your prints into plates\nDid you know that you can split a model that has a lot of parts into individual plates ready to print? This will simplify the process of keeping track of all the parts.
[hint:Speed up your print with Adaptive Layer Height]
text=Speed up your print with Adaptive Layer Height\nDid you know that you can print a model even faster, by using the Adaptive Layer Height option? Check it out!
text=Speed up your print with Adaptive Layer Height\nDid you know that you can print a model even faster by using the Adaptive Layer Height option? Check it out!
[hint:Support painting]
text=Support painting\nDid you know that you can paint the location of your supports? This feature makes it easy to place the support material only on the sections of the model that actually need it.
[hint:Different types of supports]
text=Different types of supports\nDid you know that you can choose from multiple types of supports? Tree supports work great for organic models, while saving filament and improving print speed. Check them out!
text=Different types of supports\nDid you know that you can choose from multiple types of supports? Tree supports work great for organic models while saving filament and improving print speed. Check them out!
[hint:Printing Silk Filament]
text=Printing Silk Filament\nDid you know that Silk filament needs special consideration to print it successfully? Higher temperature and lower speed are always recommended for the best results.
text=Printing Silk Filament\nDid you know that Silk filament needs special consideration to print successfully? A higher temperature and lower speed are always recommended for the best results.
[hint:Brim for better adhesion]
text=Brim for better adhesion\nDid you know that when printed models have a small contact interface with the printing surface, it's recommended to use a brim?
@@ -167,13 +167,13 @@ text = Set parameters for multiple objects\nDid you know that you can set slicin
text=Stack objects\nDid you know that you can stack objects as a whole one?
[hint:Flush into support/objects/infill]
text=Flush into support/objects/infill\nDid you know that you can reduce wasted filament by flushing it into support/objects/infill during filament change?
text=Flush into support/objects/infill\nDid you know that you can reduce wasted filament by flushing it into support/objects/infill during filament changes?
[hint:Improve strength]
text=Improve strength\nDid you know that you can use more wall loops and higher sparse infill density to improve the strength of the model?
[hint:When do you need to print with the printer door opened]
text=When do you need to print with the printer door opened?\nDid you know that opening the printer door can reduce the probability of extruder/hotend clogging when printing lower temperature filament with a higher enclosure temperature? More info about this in the Wiki.
text=When do you need to print with the printer door opened?\nDid you know that opening the printer door can reduce the probability of extruder/hotend clogging when printing lower temperature filament with a higher enclosure temperature? There is more info about this in the Wiki.
[hint:Avoid warping]
text=Avoid warping\nDid you know that when printing materials that are prone to warping such as ABS, appropriately increasing the heatbed temperature can reduce the probability of warping?
"default_materials":"Prusa Generic PLA @CORE One HF 0.4",
"family":"Prusa",
"hotend_model":"",
"machine_tech":"FFF",
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
